How to Replace the Replacement Key Battery For the Saab 9-3 Saab owners have a unique set of steps to add an additional key. It requires dealer support using the handheld computer known as Tech-2. Then it is necessary to purchase a new transponder. key are required to be purchased. Rotate your keys to stop one from wearing out faster than another. This will also help keep your keys in good condition. Replacement Case In contrast to the traditional Saab keys of old keys, the new key fobs contain electronics which makes it difficult to make a copy. This has made stealing cars much more difficult than it was twenty years ago. It also makes it more expensive to replace keys lost. Saab 9-3 owners must have two keys working. It's expensive to replace a lost key as it requires replacing the CIM module, and reprogramming the locking cylinders. Dealers charge between $100-$200 to do this. There are ways to reduce these expensive. Some parts suppliers will find the code from an old key (usually the same one that opens the doors and turns off the ignition) and cut a brand new metal key blade for only a fraction of the dealer's cost. The key must, however, be the same as the original in order to function in your car. Follow these steps to replace the case. You'll require a flathead screwdriver as well as some patience. Utilizing the screwdriver, slowly tear the plastic away and then separate the emergency key from the case. Once saab key programming near me is open remove all electronics and put them in your new case. Be sure to put the correct key and badge back in the case too. Replacement Battery The Saab 9-3 replacement battery is a budget part that can be quickly and easily replaced. This YouTube tutorial for DIY Cyclone Cyd, a user on YouTube, explains how to replace the remote key fob battery in just four steps. This tutorial can be used for any modern-day saab key fob however the procedure might differ slightly. The button is normally located close to the Saab logo on the back of the fob. The button is usually found on the back of your fob close to the Saab Logo. Then, use a flathead screwdriver into the small hole in this button. This should be sufficient to open the case so that you can change the battery. Once the new CR1632 battery is installed it is possible to reassemble the remote key fob and program it to your car. The entire process should not take more than a half hour at the most. It is a very simple procedure that doesn't require any special equipment. If you lose a key, the procedure will be more complicated, but it can still be done. The dealer has to first verify the VIN of the vehicle before requesting a replacement TWICE module and key blade with the correct unique code. Then, they'll have to cut the new key and then program it with a brand new tool for programming called MDI. Replacement Key Fob The key fob has a battery that is used to lock and unlock your car. Batteries have a limited lifespan and eventually will die. This is a typical issue that occurs with all vehicles and the good news is that you can change the batteries on most key fobs and not have to replace the whole case. Amazon sells fobs for replacement that already have all the electronics in place. It is easy to open the case and replace the batteries. You will need to remove the emergency key before you replace the batteries. To do this, you need to insert an small screwdriver with a flat head into the slot that is in the middle. Move the screwdriver around the case until it is split open, making it easier to take it out. If you're ready to replace your keys, keep an extra set on hand. This will save you lots of money. If you have an extra key, you can ask the dealer to cut the key and program it for your vehicle. This is much less expensive than purchasing a new fob. It is possible to add another key to your car in the event that you don't have one, but it requires an extensive amount of research and work. The cost for adding a second key is about a few hundred dollars and it also requires the programming of the car's computer. This can be done by a professional, however it's an expensive option for the majority of owners. Replacement Ignition The current SAAB 9-3 uses an advanced alarm system based on a key code. This means that if you lose your only working key, replacing it with an additional one could be extremely expensive as the car has to have a specific computer module installed and it must also be specifically programmed to accept an additional key. Dealers can charge hundreds of dollars to program the new key when they are not able to complete the task. If you've lost your only working key and a dealer is able to replace the computer in your car (known as the CIM or SAAB TWICE) to create a replacement, and will charge top dollar for it. We can reprogram the current EEPROM inside your car's computer to make it ready for an extra key. This will save you more than 50% of the cost you would pay at the dealer. If you've been a long time owner of an 03-11 SAAB 9-3, you likely are aware that the ignition key isn't the most robust. If the ignition key you have isn't functioning properly, you must think about replacing it. They can become sticky and the buttons have been known to fall off. The good news is that replacing the ignition key isn't as difficult as it sounds, and it can be done quickly using the proper tools.
saab key programming near me
